Stretch Packing

Do you know anything about stretching packing? It prevents the load from slipping out of the tray. This is a very progressive manifestation.

Every day, the flow of goods from the pallets during transportation can be seen, resulting in billions of dollars lost and wasted each year. If the load does not hold well for its tray, it will be a big risk.

They have different load locking methods for different stretching wrappers. , at the end of the stretch packaging film by some wrappers in the rope like an accordion, the role of the other wrapper is thin film can be rolled into the cable, the others will film wrapped, in general, are wrapped in the bottom of the tray. The most effective is that film is our research result.

Under the pressure of transportation, the general roping trend is also loosened, and its effectiveness has been reduced. However, 3 to 5 inches at the bottom of the film can be winding into a tight cable, then people can push it to the tray – compared with than its deck plate, about an inch – lock load in lower pallets in order to prevent it from sliding off.

We know that the very important thing is the location of the cable. It needs to be high enough to avoid the knife and fork pierced by forklift or pallet, and is low enough for the purpose of locking the load on the tray.

In today’s world, there are many risks. If there is a simple, inexpensive and effective way to get them to their destination, what are the reasons for your risk?

If you want to learn more about locking your load onto a tray, you can look at our video, which is how the machine rolls the film into video.

If you’re looking for ways to improve your stretching packaging process, you can also check out our eBook, packaging and weight benefits of its basic content.

 

 

Pallet

What is the safe failure of the tray fpc1? This is an unusual but serious problem.

There is a great danger lurking in our warehouse.

There is a risk in the nature of material handling. Whether it’s driving forklifts, loading pallets to trucks, or even pulling a tray of fpc1, a surprisingly high proportion of industrial accidents and sources of damage are warehouse worlds.

In the traditional sense, one of the greatest dangers is forklift. The causes of risk include weight, strength and speed. But with the continuing efforts of the occupational safety and health administration, people’s knowledge of the operational risk of forklifts has been greatly improved — for operators and bystanders. Injuries have been reduced by training and safety requirements, although there are still many.

Surprisingly, the commonly considered alternative to the tray fpc1, which is compared to the pallet fpc1 of the more secure solution, is a big risk. OSHA’s data is an interesting story, and this story is an interesting story about the tray fpc1 solution. In fact, they showed a very important point — some serious injuries were involved in the pallet jack.

Alarm tray fpc1 damage statistics

OSHA reported that in the years from 2002 to 2016, there were 56 major injuries on pallet jacks. These include:

In the total amount of time used, four-fourths of the amputees were moved, and in the aisles of the warehouse, their work was more secure than many other industrial equipment. But they should be safer.

What are the steps to ensure the safe operation of the manual tray fpc1?

Although we all know, tray fpc1 damage is impossible to be avoided completely, but, here, we can take some simple steps to ensure the safe use, and the risk is minimal.

 

 

 

Pallets

Anchor tray load how should we do it?
Twenty million pallets are being pushed off each year, which is our estimate, which leads to the results of products worth $6 billion or less. As we all know, it is a challenge for products that are not evenly packaged, such as products packaged in buckets, drums or rolls, etc. Similarly, the challenging tray packaging was also loaded with heavy offset loads. However, when these types of goods are shipped, sometimes the dealer requires them to be packaged in a tray, not just a pallet package.
The makers of large pitch coatings often move to a large box store.
The store has a demand for their products (5 gallons of asphalt seals) and he asks their products to be packed on a tray. Because their biggest customer is the big box store, manufacturers need to find a way to make this demand satisfied and quick to do what they need.
“If the goods have not been packing into the tray is our biggest client said out, refused to our fpc1 sealing machine is they began to do, it caught our attention,” a large asphalt seal manufacturers production supervisor is said so.
Packaging is easy for buckets and rolls, but packaging is key so they don’t fall off the tray during transportation. They are usually heavy, and the high level of the package is covered. During transportation, a heavy weight can be caused by sudden stop, start or vibration.
In fact, placing the product and circular circumference on the rectangular pallet is what the company is doing, which means that these products are either in the corner of the tray or out of the way. In our experience, the advantage of the product is overwhelming, so four sharp tray corners are exposed.